![reset cisco 2950 switch to default reset cisco 2950 switch to default](https://53.cdn.ekm.net/ekmps/shops/itinstock/images/cisco-catalyst-ws-c2950sx-24-24x10-100-2x1000base-sx-ports-managed-switch-[4]-48560-p.jpg)
- #RESET CISCO 2950 SWITCH TO DEFAULT HOW TO#
- #RESET CISCO 2950 SWITCH TO DEFAULT INSTALL#
- #RESET CISCO 2950 SWITCH TO DEFAULT SERIAL#
- #RESET CISCO 2950 SWITCH TO DEFAULT DRIVERS#
- #RESET CISCO 2950 SWITCH TO DEFAULT SOFTWARE#
Rename flash:config.text flash:config.old
![reset cisco 2950 switch to default reset cisco 2950 switch to default](https://cdn.slidesharecdn.com/ss_thumbnails/howtorecoverpasswordonacisco29502960switch-120118020940-phpapp02-thumbnail-4.jpg)
#RESET CISCO 2950 SWITCH TO DEFAULT HOW TO#
A pessimist might grouse at such a chore, but the optimist will see it as an opportunity to learn and practice how to perform password recovery and reset a Cisco switch back to factory defaults. This means that whomever sold me this switch did not restore it back to factory default settings. Once RealTerm was started and connected to the switch via the Console port, I pressed the ENTER key and was immediately presented with a “User Access Verification” screen and a “Password:” prompt. This way I can have two RealTerm sessions going side by side in Windows 7 or 8 by dragging the application to either the left or right side of the screen. 37 rows and 80 columns were optimal for taking up exactly 1/2 of the 1366×768 display of my screen. “baud=9600” sets the Bits per second to 9600, “port=3” sets the COM port to COM3 (you may need to check in your Device Manager to find out what port your USB-to-serial dongle is set to), “display=1” sets the display to ANSI, “rows=xx” and “cols=yy” is how many Rows and Columns of text you want your display preset to. "C:\Program Files\BEL\Realterm\realterm.exe" baud=9600 port=3 display=1 rows=37 cols=80 To make things a little easier to access RealTerm with the appropriate configuration settings, I made a shortcut to RealTerm on my desktop and used the following “Target” (found in the shortcut -> Properties)
![reset cisco 2950 switch to default reset cisco 2950 switch to default](https://i.ytimg.com/vi/-WYMZJ00S1k/maxresdefault.jpg)
#RESET CISCO 2950 SWITCH TO DEFAULT INSTALL#
Next, install and run your favorite terminal software. (These console ports are NOT Ethernet ports. The “Console” RJ-45 port on the back of a Cisco switch. A 6-foot Cisco console rollover cableĪfter getting the dongle working, plug the DB-9 connector of the baby-blue Rollover cable to the dongle and connect the RJ-45 end of the cable into the “Console” port on the back of the Cisco switch.
#RESET CISCO 2950 SWITCH TO DEFAULT DRIVERS#
Chances are your machine does not have the USB-to-Serial drivers installed already, so pop in the CD-ROM or download the drivers from the Interwebs and get the USB-to-Serial dongle working. With the USB-to-Serial dongle out of the package, the first step is to install the device drivers.
#RESET CISCO 2950 SWITCH TO DEFAULT SOFTWARE#
RealTerm terminal software (Windows free open source).
#RESET CISCO 2950 SWITCH TO DEFAULT SERIAL#
Some USB to RS-232 Serial Converter (DB-9) - I got two, so that I could connect to both switches simultaneously and not have to manually unplug and re-plug adapters in order to alternate between the two.or- Cisco Console Cable RJ45-to-DB9 (which is cheaper, but only available as an Amazon “add-on” - read: you must have $25 in your cart already…) A 6ft Rollover Console Cable (DB-9 to RJ-45) - I ordered 2.If you don’t have the appropriate tools yet, this means that 3 things will be needed to get started: a Rollover Cable, a USB-to-Serial adapter, and some Terminal software. If you already know how to physically connect to your 2950 switch, click here to jump to the Catalyst 2950 password recovery procedure. Granted, I wasn’t really expecting any since the seller had not mentioned any, but to connect to a switch that I knew nothing about, the smart bet was to connect via the RJ-45 jack (which is actually a 9600 bps serial port.) So I plugged them in, but that was all I could do because there were no Console cables (aka. Well, the two switches arrived a few days later. In my last post on the Cisco CCNA, it was mentioned that an order for two used Cisco Catalyst 2950 switches had been placed.